IBM 4232 Model 302 Manual Download

Page: 210 / 274

1. Turn the power Off (O).
2. Wait 10 seconds, then turn the power On (|).
3. If the printer displays this status code again, or if the printer

displays

call for service.

1. Press Stop.

2. Press Cancel Print.
3. Check that the serial configuration parameters are set correctly.

4. Press Start.

5. If the status code occurs again, call for service.

ð19 PRINTER BOARD FAILURE

SEE USER'S GUIDE

ð66 PRINTER BOARD FAILURE

SEE USER'S GUIDE

ð21 RECEIVE BUFFER OVERRUN

PRESS STOP THEN CANCEL PRINT

ð23 TRANSMIT BUFFER OVERRUN

PRESS STOP THEN CANCEL PRINT

ð24 PARITY ERROR

PRESS STOP THEN CANCEL PRINT

ð25 FRAMING ERROR

PRESS STOP THEN CANCEL PRINT

B-10

User’s Guide Model 302

Summary of Contents for 4232 Model 302



















































































































































































































































































Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands

IBM 4232 Model 302, Manual

Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands