IBM 4232 Model 302 Page 57 Manual Download | Manualshive

Page: 57 / 274

background image

Adjusting the Print Quality

After the printer prints a few lines, press Stop and verify that the
print quality is satisfactory. Good print quality includes:

Clear, legible print

Satisfactory darkness or lightness of output.

It is up to you to decide if the print quality is satisfactory.
Adjustments you can make that affect print quality include:

Tractor Tension

Incorrect tension on the right tractor can cause the paper holes
on the forms to tear, wrinkle, or jam in the printer. To adjust the
tractor tension, see “Adjusting the Tractor Tension” on
page 1-37.

Forms Thickness Setting

This setting can affect the darkness or lightness of output.

The printer will normally sense the forms thickness and adjust
itself automatically. However, if this setting is not correct, it can
be adjusted. To adjust the forms thickness, see “Adjusting the
Forms Thickness Setting” on page 1-38.

Note: The Automatic Forms Thickness Adjustment (AFTA)
mechanism automatically measures the forms thickness and
adjusts the gap from the print head to the platen rod based on
the measured value. See “Automatic Forms Thickness
Adjustment (AFTA)” on page 2-8 for information on how the
printer sets the forms thickness.

Forms Tension

Incorrect tension on the forms can cause forms to tear, wrinkle,
or buckle and can affect the appearance of the output. To adjust
the forms tension, see “Adjusting the Forms Tension” on
page 1-40.

Chapter 1. Setting Up the 4232 Printer Model 302

1-35

«
...
55
56
57
58
59
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

imagePROGRAF iPF8400

Brand: Canon Pages: 157

Brand: Canon Pages: 91

Brand: Xerox Pages: 341

Figure 4 Standalone

Brand: 3D Systems Pages: 2

Brand: UniFlow Pages: 42

Brand: Xerox Pages: 532

Brand: Xerox Pages: 174

Phaser 6115 MFP

Brand: Xerox Pages: 2

Phaser 6115 MFP

Brand: Xerox Pages: 219

Brand: Xerox Pages: 5

Brand: Xerox Pages: 3

Phaser 6128 MFP

Brand: Xerox Pages: 2

Phaser 6128 MFP

Brand: Xerox Pages: 16

Brand: Xerox Pages: 2

Brand: Xerox Pages: 9

Brand: Xerox Pages: 12

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands