manualshive.com logo in svg

IBM 4232 Model 302, Manual

Share
Download
IBM 4232 Model 302 Manual Download Page 175

 

 
 

Chapter 4. Using the Operator Print Tests

This chapter describes the print tests you can perform to:

Ÿ

Demonstrate printing capabilities

Ÿ

Adjust printer operations

Ÿ

Check the printer configuration

Ÿ

Check printer operation.

Any of these tests can be performed at anytime. However, all tests
should be performed when there is no print data buffered in the
printer processing. When you go into test mode, the printer goes
offline. When you exit test mode, the printer performs a

 partial reset

before going back online. This partial reset clears any buffered print
data and anything stored in printer storage, such as downloaded
fonts or overlays.

Entering the Operator Print Tests may cause the forms configuration
settings to be adjusted. If the current settings are less than a
maximum print position of 72 or a maximum page length of 66, the
printer will adjust the settings to a standard 8.5 x 11 inch page.
This is done to ensure correct formatting of all offline customer tests.
The original settings will be reset when the printer returns to the
online state. If the settings are larger than the required page
dimensions, the settings are not changed.

General Test Instructions

To enter the Operator Print Tests menu, press Test when the printer
is 

not ready. The printer displays

The Printer Demonstration test is the first test in the Operator Print
Tests menu. From this display, press Scroll 

↑

 or Scroll 

↓

 to view

the other tests.

OPERATOR PRINT TESTS
Printer Demonstration

 Copyright IBM Corp. 1993, 1994 

 

4-1

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands