IBM 4232 Model 302 Manual Download

Page: 116 / 274

5. Press Scroll

↑

or Scroll

↓

until the printer displays

6. Press Enter or Start to begin this test.

The printer displays

7. Carefully feed the form under the lower forms guide. Use the

left edge of the lower forms guide to help feed the form in
straight. Feed the form until the top edge touches both the

left

and

right feed rollers. Continue to hold the form.

Lo w e r
Forms Guide

The printer displays

8. Press Load/Eject. As the printer begins to pull in the form,

release the form. The Ready indicator comes on, and printing
begins.

OPERATOR PRINT TESTS
Printer Verification

ð13 DATA TO PRINT

LOAD FORMS

ðð4 PRESS LOAD

1-94

User’s Guide Model 302

Summary of Contents for 4232 Model 302



















































































































































































































































































Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands

IBM 4232 Model 302, Manual

Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands