manualshive.com logo in svg

IBM 4232 Model 302, Manual

Share
Download
IBM 4232 Model 302 Manual Download Page 159

 

 
 

Dual Purpose Forms Device (F2)

B o t t o m M e t a l B a r

C l i p s

T o p o f F o r m s D e v i c e

T e a r B a r

The device has an 

F2 surrounded by a square in the upper left

corner of the device.

Use this device when printing work that requires you to separate the
continuous forms between transactions and for most general printing
requirements on continuous forms. Use the 

tear bar to separate the

printed forms. Also, the automatic loading feature (

autoload) is

enabled for this device.

See “Installing and Using the Dual Purpose Forms Device (F2)” on
page 1-53 for information on installing and removing the forms
device, loading and unloading forms, and adjusting the device.

   

Chapter 2. Getting to Know Your Printer

2-17

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands