IBM 4232 Model 302 Manual Download | Manualshive

Page: 216 / 274

background image

The OCR-A and OCR-B print languages have fixed CPI and Print
Quality settings. For these print languages, the CPI must be set to
10 CPI and the Print Quality must be set to NLQ. While the
Configuration Menu allows scrolling through the various selections,
this message is displayed if either the CPI or Print Quality is
changed when the print language is set to OCR-A or OCR-B.

Note: When the print language is changed to any language other
than OCR-A or OCR-B, these options become enabled. They are,
however, left at 10 CPI and NLQ and require reconfiguring if these
settings are not suitable.

This message is displayed when either the access cover or the
paper door is opened and the printer is in the

not ready state. The

not ready state is reached when Stop is pressed from the ready
state. If the printer is made ready and a print job is started, the
printer runs at a reduced speed if either the access or the paper door
cover is left open.

|

This message is displayed when Menu is pressed when the Menu

|

Lock feature is enabled. Contact your system programmer.

ð95 OPTION NOT AVAILABLE

Change Print Language

ð96 NOT READY

COVER/DOOR OPEN

|

ð97 FUNCTION NOT AVAILABLE

|

MENU LOCKED

B-16

User’s Guide Model 302

«
...
214
215
216
217
218
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 8

Brand: NCR Pages: 224

SelfServ Checkout 7350

Brand: NCR Pages: 20

Brand: Canon Pages: 21

imageRUNNER ADVANCE 4251

Brand: Canon Pages: 12

Pixma TS7700i Series

Brand: Canon Pages: 554

Brand: Synology Pages: 15

Brand: Oki Pages: 192

Brand: Muratec Pages: 6

Brand: IriSys Pages: 21

Makerspace 91413

Brand: Mooreco Pages: 10

Brand: Felix Storch Pages: 46

WorkCentre 6400XF

Brand: Xerox Pages: 24

ID MAKER Zenius

Brand: IDVille Pages: 66

1235/DX - Phaser Color Laser Printer

Brand: Xerox Pages: 144

Brand: Nashuatec Pages: 177

Brand: Canon Pages: 8

Brand: Canon Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands