IBM 4232 Model 302 Page 138 Manual Download | Manualshive

Page: 138 / 274

background image

Attaching the 4232 Printer Model 302 to Your
Computer

This section provides specific instructions on attaching the printer to
your computer. Supported devices include:

IBM Personal Computer

IBM Personal System/2*

IBM RISC System/6000*

IBM AS/400* with ASCII controller

IBM 4033 LAN Adapter.

|

IBM System/390

Connecting to the Parallel or Serial Interface

Parallel or serial cables are not shipped with your printer. If you do
not have a cable, contact your IBM marketing representative. The
following table provides the information you need to purchase the
correct cable.

Interface

Part Name

Part Number

Cable Length

Parallel

Parallel Cable

1525612

1.8 m (6 ft)

Serial
RS-232C

Serial Cable

8509386

6 m (20 ft)

Serial
RS-422A

Serial Cable

70X8652

15.2 m (50 ft)

Attaching a Parallel Cable

CAUTION:

Make sure the machine is turned Off (O) before you connect
or disconnect the power cord or other cables.

If the machine has cables other than the power cord, you
must connect them before you plug the power cord into an
outlet. You must first unplug the power cord from the outlet
when you remove the other cables.

1-116

User’s Guide Model 302

«
...
136
137
138
139
140
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Brand: Xerox Pages: 532

Brand: Xerox Pages: 174

Phaser 6115 MFP

Brand: Xerox Pages: 2

Phaser 6115 MFP

Brand: Xerox Pages: 219

Brand: Xerox Pages: 5

Brand: Xerox Pages: 3

Phaser 6128 MFP

Brand: Xerox Pages: 2

Phaser 6128 MFP

Brand: Xerox Pages: 16

Brand: Xerox Pages: 2

Brand: Xerox Pages: 9

Brand: Xerox Pages: 12

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands