IBM 4232 Model 302 Manual Download | Manualshive

Page: 128 / 274

background image

Adjusting the Print Alignment
You can adjust dot registration and print quality for characters
created using bidirectional printing. The bidirectional alignment may
need periodic adjustment to maintain print quality.

To change the bidirectional alignment, follow these steps:

1. If the printer is

ready, press Stop.

The printer displays

2. Press Test.

The printer displays

3. Press Scroll

↓

or Scroll

↑

until the printer displays

4. Press Enter or Start to begin this test.

The printer displays

NOT READY

<A>

OPERATOR PRINT TESTS
Printer Demonstration

OPERATOR PRINT TESTS
Bidirectional Adjustment

ð13 DATA TO PRINT

LOAD FORMS

1-106

User’s Guide Model 302

«
...
126
127
128
129
130
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

ImageCLASS MF4570dw

Brand: Canon Pages: 164

imagePRESS C800 Series

Brand: Canon Pages: 132

ImageCLASS MF5730

Brand: Canon Pages: 2

Brand: Oki Pages: 6

Brand: Oki Pages: 44

Brand: Oki Pages: 13

Brand: Oki Pages: 20

Brand: Oki Pages: 2

Brand: Oki Pages: 28

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands