IBM 4232 Model 302 Manual Download | Manualshive

Page: 230 / 274

background image

Problem: Forms do not feed past print head

1: The Automatic Forms Thickness Adjustment (AFTA) setting

needs to be changed.
Solution: See the procedure for adjusting the forms thickness
setting through the operator panel (based on your forms device)
in Chapter 1, “Setting Up the 4232 Printer Model 302.”

2: The forms device is not properly installed.

Solution: Check the forms device installation (see Chapter 1,
“Setting Up the 4232 Printer Model 302”).

3: The ribbon is twisting or folding.

Solution: Replace the ribbon.

4: The forms device is defective.

Solution: See “Forms Device Inspection” on page B-24.

5: The ribbon shield is damaged.

Solution: Replace the ribbon.

B-30

User’s Guide Model 302

«
...
228
229
230
231
232
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: Felix printers Pages: 9

Brand: Felix printers Pages: 15

Brand: Felix printers Pages: 15

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Brand: EBS Pages: 34

Brand: JCM Pages: 22

Brand: NCR Pages: 224

SelfServ Checkout 7350

Brand: NCR Pages: 20

Brand: Xerox Pages: 16

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 6

VersaLink C405/N

Brand: Xerox Pages: 256

Brand: Cycjet Pages: 26

Brand: Xerox Pages: 55

Brand: ABLE Systems Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands