Huawei FusionModule1000B V100R003C00 Page 5 Commissioning Manual Download

Page: 5 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

Contents

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Contents

About This Document .................................................................................................................... ii

1 Precautions for Power-On Commissioning ............................................................................. 1

2 Basic Rules for Power-On Commissioning ............................................................................. 2

3 General power-on commissioning process .............................................................................. 3

4 Preparations for Power-On Commissioning ........................................................................... 4

4.1 Tool Preparations .......................................................................................................................................................... 4

4.2 Obtaining Technical Documents ................................................................................................................................... 5

4.3 Commissioning Personnel Skill Requirements ............................................................................................................. 7

4.4 Preparing for the Power Supply and Distribution System Power-On Commissioning ................................................. 8

4.5 Preparing for the Cooling System Power-On Commissioning ..................................................................................... 9

4.5.1 Preparation Process .................................................................................................................................................... 9

4.5.2 Material preparations for the secondary refrigerant ................................................................................................... 9

4.5.3 Configuring Cooling Components ........................................................................................................................... 13

4.5.4 Verifying the Setting of the Automatic Water Refill Valve ...................................................................................... 16

4.5.5 Switching Valves for Filling Secondary Refrigerant ............................................................................................... 18

4.5.6 Filling Secondary Refrigerant .................................................................................................................................. 19

4.5.7 Expelling Air from the Cooling System ................................................................................................................... 21

4.5.7.1 Expelling Air from the Expansion Tanks .............................................................................................................. 21

4.5.7.2 Expelling Air from the LCU ................................................................................................................................. 23

4.5.7.3 Expelling Air from Chillers .................................................................................................................................. 24

4.5.8 Switching Valves to the Operating State .................................................................................................................. 28

4.6 Preparing for the Management System Power-On Commissioning ........................................................................... 29

4.7 Preparing for the Fire Extinguishing System Power-On Commissioning................................................................... 29

4.8 (Optional) Auxiliary Heating for Extra Low Temperatures ........................................................................................ 30

5 Items to Be Checked Before Power-On .................................................................................. 32

6 Power-On Commissioning ........................................................................................................ 36

6.1 General Power-On Commissioning Process ............................................................................................................... 36

6.2 Power-On Commissioning .......................................................................................................................................... 37

6.3 Normal Power-On Checking for Components ............................................................................................................ 38

7 System Commissioning ............................................................................................................. 44

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands