Huawei FusionModule1000B V100R003C00 Page 13 Commissioning Manual Download

Page: 13 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

4 Preparations for Power-On Commissioning

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Technical Manual

Function

Obtaining Method
(Remarks)

UPS5000-E-(40 kVA-320
kVA) User Manual

Describes how to
commission the
UPS5000-E.

Download this document
from

http://e.huawei.com

UPS5000-E-(20 kVA-160
kVA) User Manual (Low
Voltage)

Describes how to
commission the
UPS5000-E.

Download this document
from

http://e.huawei.com

FusionModule1000B
V100R003C00 Outsourced
Component Document
Package

Describes how to power on
and commission each
component.

Downloaded from

http://3ms.huawei.com

. If

the link is not available,
contact onsite Huawei
engineers.

4.3 Commissioning Personnel Skill Requirements

Table 4-3

describes the skill requirements for the FusionModule1000 commissioning

personnel.

Table 4-3

Skill requirements for the FusionModule1000 commissioning personnel

Field

Personnel Skill Requirement

Power supply and
distribution system

Familiar with the power supply and distribution system
configurations and the operations for each core component in the
FusionModule1000

With power distribution engineer qualifications

Cooling system

Familiar with the cooling system configurations and the operations
for each core component in the FusionModule1000

With cooling engineer qualifications

Management
system

With knowledge in the hardware and software of the container data
center, familiar with basic communications protocols, familiar with
equipment interfaces in extra low voltage (ELV) systems, and
proficient in operating the NetEco management system

With ELV engineer qualifications

Fire extinguishing
system

Familiar with the fire extinguishing system configurations and the
operations for each core component in the FusionModule1000

With fire protection engineer qualifications

Lighting and
structural systems

Familiar with the overall configurations and layout of the
FusionModule1000

Experienced in data center maintenance

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands