manualshive.com logo in svg

Huawei FusionModule1000B V100R003C00, Commissioning Manual, Page: 88 / 111

Share
Download
Huawei FusionModule1000B V100R003C00 Commissioning Manual Download Page 88

FusionModule1000B Water-Cooled IT Solution 
Commissioning Guide 

9 Commissioning Core Components 

 

Issue 02 (2017-01-10) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

82 

 

 

 

When powering on and commissioning the 30 kW chilled water precision air conditioner, 
you are not allowed to modify the initial configurations of the 30 kW chilled water 
precision air conditioner unless you are authorized by onsite Huawei engineers. 

 

For the initial DIP switch configuration for the remote temperature sensor, see 

9.2.2.1 

Initial DIP Switch Configuration for T/H Sensors

. 

 

For the initial DIP switch configuration for the main control board, see 

9.2.2.2 Initial DIP 

Configuration for the Main Control Board

. 

 

For the initial teamwork configuration, see 

9.2.2.3 Teamwork Initial Configuration

. 

 

For the initial configuration of temperature and humidity, see 

9.2.2.4 Initial Configuration 

of Temperature and Humidity

. 

 

9.2.2.3 Teamwork Initial Configuration

 and 

9.2.2.4 Initial Configuration of Temperature 

and Humidity

 must be configured after power-on. 

Step 3

 

Tap 

Indicates

 on the main screen, and tap 

Confirm

 on the dialog box that appears. If the start 

succeeds, the system prompts that the command is successfully executed. 

----End 

9.2.2.1 Initial DIP Switch Configuration for T/H Sensors 

Prerequisites 

You have powered on the 30 kW chilled water precision air conditioners. 

Preparations 

Tools: none 

Document required: initial DIP switch settings table for the remote T/H sensor of the 30 kW 
chilled water precision air conditioner 

Skill requirement: cooling engineer 

 

For the tables, see the initial configuration parameter manual for the solution in use. 

Context 

Each 30 kW chilled water precision air conditioner is equipped with three remote T/H sensors 
at the air return vent. A maximum of six remote T/H sensors can be configured.   

You need to set the DIP switches for the remote T/H sensors before using the sensors.   

Summary of Contents for FusionModule1000B V100R003C00
















































































































Reviews:

No comments