Huawei FusionModule1000B V100R003C00 Page 74 Commissioning Manual Download

Page: 74 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Commissioning Core Components

9.1 Commissioning Power Distribution Components

9.1.1 Commissioning the Power Distribution Cabinet

Prerequisites



You have verified all the specifications for the power-on.



You have put on protective articles.

Preparations

Tool: multimeter

Documents: power supply and distribution system diagrams, power supply and distribution
component layout

Skill requirement: power distribution system engineer

For the diagrams, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Switch on the input power circuit breaker to power on the PDC.



The input power circuit breaker refers to the output circuit breaker that controls power supply from
the upstream power distribution equipment to the PDC.



If the indicators (if configured) on the PDC have turned on, the PDC has been powered on.



The general PDC circuit breaker can be an ATS, MCCB, or MCB.

(Optional) If an ATS is configured, go to

Step 2

(Optional) If an MCCB or MCB is configured, go to

Step 3

Step 2

(Optional) Commission the ATS.

The ATS is an 8D ATS.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands