manualshive.com logo in svg

Huawei FusionModule1000B V100R003C00, Commissioning Manual, Page: 51 / 111

Share
Download
Huawei FusionModule1000B V100R003C00 Commissioning Manual Download Page 51

FusionModule1000B Water-Cooled IT Solution 
Commissioning Guide 

7 System Commissioning 

 

Issue 02 (2017-01-10) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

45 

 

 

When the RH2288 server switches between the two power supplies, if the server does not restart or 
break down, the power supply switchover meets the requirements. 

----End 

7.1.2 Commissioning the Logic Load Disconnection 
(Powering-Off) of the Power Supply System Under Normal 
Temperature 

Prerequisites 

The FusionModule1000 is powered on, commissioned, and working properly. 

Preparations 

Tools: none 

Documents: power supply and distribution system diagrams, power supply and distribution 
component layout 

Skill requirement: power distribution system engineer 

 

For the diagrams, see the initial configuration parameter manual for the solution in use. 

Procedure 

Step 1

 

Power off the FusionModule1000 by referring to 

8 Shutting Down and Powering Off

.   

 

 

 

Save parameters before power-off. 

 

Power off the devices in the normal power-off logic sequence. 

Step 2

 

Verify whether the system and components are intact and working properly. 

 

If yes, go to 

Step 3

. 

 

If no, locate and rectify the fault. Then go to 

Step 3

. 

Step 3

 

Power off the FusionModule1000 by following instructions in 

6 Power-On Commissioning

.   

Step 4

 

Verify whether the systems run stably after power-on. 

 

The FusionModule1000 meets requirements if its components are intact and systems are normal after 
powered off, and systems run stably after power-on. 

----End 

Summary of Contents for FusionModule1000B V100R003C00
















































































































Reviews:

No comments