Huawei FusionModule1000B V100R003C00 Commissioning Manual Download Page 42

Page: 42 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

6 Power-On Commissioning

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Power-On Commissioning

6.1 General Power-On Commissioning Process

Precautions

The power supply and distribution system for the water-cooled prefabricated modular data
center IT solution has two configurations: 2N and N+X. Determine the commissioning
process based on the actual configuration.

This section describes the general power-on commissioning process for the water-cooled
prefabricated modular data center IT solution.

2N Power Supply and Distribution System

Figure 6-1

Power-on commissioning process for the 2N power supply and distribution system

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Huawei FusionModule1000B V100R003C00, Commissioning Manual, Page: 42 / 111

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews: