Huawei FusionModule1000B V100R003C00 Commissioning Manual Download

Page: 105 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Press

S12

again to display month and date in the format of

? ? ? ?

. Press

S11

to adjust

the month, which changes cyclically between 1 and 12. Then press

S10

to adjust the date,

which changes cyclically between 1 and 31.

Press

S12

again to display hour and minute in the format of

? ?:? ?

. Press

S11

to adjust

the hour, which ranges from 0 to 23. Then press

S10

to adjust the minute, which ranges

from 0 to 59.

Press

S12

again to finish the time setting. The indicator H11 goes off. The nixie tube

displays the hour and minute.

Step 5

Start or stop the fire alarm sounder.

When the keypad is unlocked, press

ALARM BELL

to start or stop the fire alarm sounder.

After the fire alarm sounder is started, the indicator beside the button turns on.

Step 6

Start or stop the fire alarm horn/strobe.

When the keypad is unlocked, press

HORN/STROBE

to start or stop the fire alarm

horn/strobe. After the alarm is started, the indicator beside the button turns on.

----End

9.4.2 Commissioning the Emergency Lights (standard)

Prerequisites

The sockets of the emergency light have been powered on.

Preparations

Tools: step ladder, needle-shaped tool

Documents required: power supply and distribution system diagrams, fire extinguishing
device layout diagram (standard)

Skill requirement: fire engineer

For the diagrams, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

When you press down the

TEST

button on the emergency light, the emergency light turns on.

When you release the

TEST

button, the emergency light turns off.

Step 2

When you unplug the power plug of the emergency light, the emergency light turns on. When
you stab the small hole shown in the figure with a needle-shaped tool, the emergency light
turns off.



You can also turn off the emergency light by pressing and holding the

TEST

button for more than

5s.



If the result expected for each step appears, the emergency light is working properly.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands