manualshive.com logo in svg

Huawei FusionModule1000B V100R003C00, Commissioning Manual, Page: 3 / 111

Share
Download
Huawei FusionModule1000B V100R003C00 Commissioning Manual Download Page 3

FusionModule1000B Water-Cooled IT Solution 
Commissioning Guide 

About This Document 

 

Issue 02 (2017-01-10) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

ii 

 

About This Document 

Purpose 

This document describes how to power on and commission the FusionModule1000B 
prefabricated modular data center solution (FusionModule1000B for short) in terms of 
power-on commissioning preparations, checking items and precautions, power-on check, 
power-on commissioning, joint commissioning, and power-off. This document also describes 
the power-on commissioning, joint commissioning, and power-off methods for core 
components of the solution. It provides you a quick grasp of the commissioning method. 

Intended Audience 

This document is intended for: 

 

Commissioning engineers 

 

Technical support engineers 

 

System engineers 

 

Maintenance engineers 

Symbol Conventions 

The symbols that may be found in this document are defined as follows. 

Symbol 

Description 

 

Indicates an imminently hazardous situation which, if 
not avoided, will result in death or serious injury. 

 

Indicates a potentially hazardous situation which, if not 
avoided, could result in death or serious injury. 

 

Indicates a potentially hazardous situation which, if not 
avoided, may result in minor or moderate injury. 

Summary of Contents for FusionModule1000B V100R003C00
















































































































Reviews:

No comments