Huawei FusionModule1000B V100R003C00 Page 75 Commissioning Manual Download

Page: 75 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

(Optional) If an 8D ATS is configured, go to

9.1.1.1 (Optional) Commissioning the 8D

ATS

to perform the commissioning.

After the ATS is commissioned, go to

Step 3

Step 3

Switch on the SPD circuit breaker in the PDC to power on the SPD. The SPD indicators
become steady green.

Step 4

Commission monitoring devices in the PDC.

A PDC can be equipped with monitoring components such as an electricity meter or MDU. In certain
scenarios, no monitoring component is installed.

(Optional) If a PD510 electricity meter is configured, go to

Step 5

(Optional) If an MDU is configured, go to

Step 6

(Optional) If no monitoring component is configured, go to

Step 7

Step 5

(Optional) Commission the PD510 electricity meter.

For details, see

9.1.1.2 (Optional) Commissioning the PD510 Electricity Meter

After ensuring that the electricity meter works properly, go to

Step 7

Step 6

(Optional) Commission the MDU.

For details, see

9.1.1.3 (Optional) Commissioning the MDU

After ensuring that the MDU works properly, go to

Step 7

Step 7

Switch on the output circuit breakers in the PDC level by level as required to supply power to
downstream equipment.

----End

9.1.1.1 (Optional) Commissioning the 8D ATS

Prerequisites

You have powered on the 8D ATS.

Preparations

Tool: multimeter

Documents: documents delivered with the 8D ATS, 8D ATS initial configuration table, power
supply and distribution system diagram

Skill requirement: power distribution system engineer

For the diagrams and tables, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Check whether any alarm is displayed on the 8D ATS controller. If an alarm is displayed,
clear the alarm by following instructions in the delivered documents.

Step 2

Verify 8D ATS configurations by referring to the 8D ATS initial configuration table and
documents delivered with the 8D ATS.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands