Huawei FusionModule1000B V100R003C00 Commissioning Manual Download Page 72

Page: 72 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

8 Shutting Down and Powering Off

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Shutting Down and Powering Off

Prerequisites

You have been permitted to power off the FusionModule1000.

Preparations

Tools: portable light

Document: power supply and distribution system diagram

Skill requirement: power distribution system engineer

For the diagrams, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Shut down servers and storage devices.



Save parameters before power-off.



Power off the devices in the normal power-off logic sequence.

Step 2

Shut down the RH2288 server and VCN500.

Step 3

Shut down air conditioners.

Step 4

Switch off circuit breakers level by level to power off devices by referring to the power
supply and distribution system diagram.

During the power-off process, there is no fire or other exception, but the fire control panel displays a
power failure alarm. Ignore the alarm.

Step 5

Switch off the external power input circuit breaker of the FusionModule1000.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Huawei FusionModule1000B V100R003C00, Commissioning Manual, Page: 72 / 111

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews: