Huawei FusionModule1000B V100R003C00 Page 22 Commissioning Manual Download

Page: 22 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

4 Preparations for Power-On Commissioning

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

----End

4.5.4 Verifying the Setting of the Automatic Water Refill Valve

Prerequisites

The water pressure of the auxiliary water refill device meets the requirement.

Preparations

Tool: adjustable wrench

Documents: pipe system diagram, pipe system valve control relationship table

Skill requirement: cooling engineer

For the diagrams and tables, see the initial configuration parameter manual for the solution in use.

Context

The setting of the automatic water refill valve is critical for the stable running of the cooling
system.

The automatic water refill valve has been factory set to 0.15 MPa. In case of accidental
changes during the transportation or installation, verify the valve setting before starting the
system.

Procedure

Step 1

Close the service valve for the automatic water refill valve.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands