Huawei FusionCol8000-E240 User Manual Download Page 197

Page: 197 / 305

8.5.2 Component Position (FDC Scenario)

Figure 8-2 Components to be replaced

(1) Differential

pressure switch

(2) Indoor return air

T/H sensor

(3) Outdoor intake air

filter

(4) Exhaust fan

(5) Outdoor air intake

T/H sensor

(6) Spray pump

(7) Air supply fan

(8) Compressor

(9) Compressor drive

(10) Liquid level sensor (11) Fan drive

8.5.3 Replacing an Air Filter (Building Scenario)

Prerequisites

●

An air filter needs to be replaced.

●

A spare air filter of the same model is available and functional.

●

When replacing an air filter, you need to use a maintenance platform. For

details how to prepare the platform, see

F Air filter Maintenance Platform

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the device

switch in the PDF.

NO TICE

Exercise caution because the device is still energized after it is shut down on the

screen of the display module.

Step 2 Replace the outdoor intake air filter (end). Remove the air filter fasteners and take

out the air filter from the end.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

188

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands