Huawei FusionCol8000-E240 User Manual Download Page 272

Page: 272 / 305

Menu

Parameter

Description

High

humidity

alarm

When detecting that the alarm value is

greater than the threshold, the system

generates an alarm.

Low

humidity

alarm

When detecting that the alarm value is

greater than the threshold, the system

generates an alarm.

Settings > Alarm

Settings >

Mainboard

Return air

filter

blocked

alarm

● Enable: Alarms are reported to the

NMS. Active alarms are displayed on

the display module and the system

performs related protection actions.

● Disable: No alarms are generated and

no protection actions are performed.

Primary

power

failure alarm

● Enable: Alarms are reported to the

NMS. Active alarms are displayed on

the display module and the system

performs related protection actions.

● Disable: No alarms are generated and

no protection actions are performed.

SPD and

voltage

detection

board comm

failed

● Enable: Alarms are reported to the

NMS. Active alarms are displayed on

the display module and the system

performs related protection actions.

● Disable: No alarms are generated and

no protection actions are performed.

Backup

power

failure alarm

● Enable: Alarms are reported to the

NMS. Active alarms are displayed on

the display module and the system

performs related protection actions.

● Disable: No alarms are generated and

no protection actions are performed.

Outdoor

intake air

filter

blocked

alarm

● Enable: Alarms are reported to the

NMS. Active alarms are displayed on

the display module and the system

performs related protection actions.

● Disable: No alarms are generated and

no protection actions are performed.

Power

voltage

abnormal

Specifies the threshold.

NOTE

Use the default value.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

C Parameter Description

Issue 02 (2021-04-15)

263

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands