Huawei FusionCol8000-E240 User Manual Download Page 223

Page: 223 / 305

Figure 8-31 Injecting nitrogen to preserve the pressure

(1) Nitrogen cylinder

(2) Reducing valve

(3) Low pressure gauge

(4) High pressure gauge

(5) Low pressure needle valve (6) Liquid pipe needle valve

NO TICE

The outlet pressure of the reducing valve should be within 3.0 MPa; otherwise,

components may be damaged.

Step 2 Open the pressure gauges and reducing valve. Inject 3.0 MPa nitrogen and

preserve the pressure for 24 hours. The system pressure should stay constant

under unchanging ambient temperature conditions. If there is considerable

temperature change, perform the test again.

NO TICE

The outlet pressure of the reducing valve should be within 3.0 MPa; otherwise,

components may be damaged.

Step 3 If the pressure decreases, apply soapy water or use a halogen leak detector to

check for any leakage. If the pressure is stable, expel the nitrogen.

----End

8.5.15.4 Vacuumizing and Precharging Refrigerant

CA UTION

During the commissioning of the smart cooling product, ensure that no

combustion-supporting materials (such as air or additive) enter the smart cooling

product system. Huawei is not liable for any risks and losses caused due to

violation.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

214

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands