Huawei FusionCol8000-E240 User Manual Download Page 36

Page: 36 / 305

Item

Specifications

(Building Scenario)

Specifications (FDC Scenario)

Test conditions: The outdoor dry and wet bulb temperatures are 35°C and 27°C

respectively; the indoor return and supply air temperatures are 38°C at 25% RH

and 25°C at 50% RH respectively; the external residual pressures of the indoor

and outdoor units are 150 Pa and 100 Pa respectively. If the indoor return air

temperature is lower than 38°C, the cooling capacity of the equipment is

derated.

Table 2-6 Compressor cooling specifications

Item

Specifications

Compressor type

Variable-frequency scroll compressor

Number of compressors

Throttling device

Electronic expansion valve (EEV)

Refrigerant

R410A

2.7 Working Modes

The unit runs in one of the following modes based on the real-time working

conditions and load.

Table 2-7 Cooling modes

Cooling Mode

Fan

Status

Water

Pump

Status

Compressor

Status

Dry mode (fan)

Off

Wet mode (fan + spraying)

Off

Dry mode + Auxiliary cooling

mode (fan + compressor

cooling)

Off

Wet mode + Auxiliary cooling

mode (fan + sp

compressor cooling)

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Issue 02 (2021-04-15)

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands