Huawei FusionCol8000-E240 User Manual Download Page 269

Page: 269 / 305

Menu

Parameter

Description

Settings > Comm

Settings > WIFI

Settings

WiFi SSID

Set WiFi SSID based on the actual

configuration. WiFi SSID is the name

used for the WiFi hotspot over which a

mobile phone connects to smart cooling

product.

WiFi

password

Enter the WiFi password when you use a

mobile phone to connect to the WiFi. The

WiFi has no default password. When you

enable the WiFi function for the first

time, you need to set a password.

Enable WiFi

Enables the WiFi function of the smart

cooling product.

WiFi group

sharing

enable

When Enable WiFi is set to Enable, the

mobile phone can access the smart

cooling product in the same FE cascading

network when connecting to the WiFi of

the smart cooling product.

Settings > Comm

Settings > Modbus

Settings

Baud rate

Set the baud rate as required. The value

should be consistent with that set on the

NMS.

Communicat

ion address

Enter the communications address of the

smart cooling product as planned. The

NMS communicates with the smart

cooling product using this address, and

the communications addresses of two

smart cooling products connected to the

same NMS must be different.

RS485

monitoring

grouping

● For scenarios without grouping, set

this parameter to Enable for the last

device.

● For scenarios with grouping, set this

parameter to Enable for the last

device in each teamwork control

group.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

C Parameter Description

Issue 02 (2021-04-15)

260

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands