Huawei FusionCol8000-E240 User Manual Download Page 113

Page: 113 / 305

Menu

Parameter

Setting Guide

Settings > Quick

Settings > Comm

Settings

Modbus

Comm

address

Enter the communication address

planned for the smart cooling

product. The NMS communicates

with the smart cooling product

through this address.

NOTE

The communication addresses of the two

smart cooling products connected to the

same NMS must be different.

----End

Follow-up Procedure

After power-on, choose Running > Device Details > Compressor on the home

screen to view the compressor parameters and status.

Figure 6-2 Compressor

6.3 Home Screen

The home screen of the display module displays the system status and allows you

to access other function menus, such as Running, Alarms and Settings.

NO TICE

The information in the screenshots is for reference only. The actual parameters

prevail.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

6 Power-On Commissioning

Issue 02 (2021-04-15)

104

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands