Huawei FusionCol8000-E240 User Manual Download Page 131

Page: 131 / 305

Figure 6-17 Setting SNMP port

NO TE

SNMP Port is set to 161 by default.

Step 6 Tap Next Page.

Step 7 Set SNMP trap parameters.

1. Tap Add under SNMP Trap.
2. Set Trap Address as planned and Trap Port to the actual port number.

NO TE

Trap Port is set to null by default.

3. Select the SNMP Version. If a SNMPv3 user is configured, it is recommended

that SNMP Version be set to SNMPv3.

4. If SNMP Version is set to SNMPv3, you need to select SNMPv3 User Name.

Figure 6-18 Setting SNMP trap parameters

5. Tap Submit under SNMP Trap.

----End

Follow-up Procedure

After a USB flash drive has been inserted into the USB port of the main control

module and successfully identified, tap Export File under MIB File to export the

MIB file to the USB flash drive for the customer's use in accessing a third-party

NMS.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

6 Power-On Commissioning

Issue 02 (2021-04-15)

122

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands