Huawei FusionCol8000-E240 User Manual Download Page 217

Page: 217 / 305

Step 2 Remove the adjustable side panel and beam from the precooling module to be

maintained.

Step 3 Remove the sheet metal from the precooling module to be maintained.

Step 4 Pull out the precooling module horizontally by holding its handles.

Figure 8-27 Replacing a precooling module

Step 5 Install the new precooling module and secure the sheet metal.

Step 6 Install the adjustable side panel and beam.

Step 7 Tap Start on the home screen. Ensure that the device is running normally without

any alarms.

----End

8.5.15 Replacing a Compressor

8.5.15.1 Replacing a Compressor

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

208

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Huawei FusionCol8000-E240, User Manual, Page: 217 / 305

Search results

Summary of Contents for FusionCol8000-E240

Reviews: