Huawei FusionCol8000-E240 User Manual Download Page 270

Page: 270 / 305

Menu

Parameter

Description

Link mode

● Server: The smart cooling product

works as the server and can connect

to two clients for communication.

● Client: The smart cooling product

works as the client and can connect to

a remote server for communication.

● Server and client: The smart cooling

product works as the server and can

connect to two clients for

communication. It also works as the

client and can connect to a remote

server for communication.

Client

encryption

This parameter is configurable when Link

mode is set to Client.

Server

encryption

This parameter is configurable when Link

mode is set to Server.

Encryption

operation

CBC

Enable, Disable

NOTE

Indicates whether to use the CBC encryption

algorithm. When you set this parameter, a

dialog box is displayed, indicating that the

system will automatically restart. Select an

option based on the site requirements.

NMS IP

address

Enter the actual IP address of the NMS.

IP addresses of the display panel, client

NMS, and server NMS must be unique.

This parameter is configurable when Link

mode is set to Client.

NMS port

number

It is recommended that you retain the

default value. If you need to change the

value, enter a value as required. This

parameter is configurable when Link

mode is set to Client.

Pre-shared

password

Secondary authentication password used

for Modbus-TCP connection.

Settings > Comm

Settings > SNMP

Settings

For details, see the section "Setting Communications

Parameters."

Settings > Alarm

Settings > T/H

Sensor

Supply air*

temperature

sensor fault

● Enable: Alarms are reported to the

NMS. Active alarms are displayed on

the display module and the system

performs related protection actions.

● Disable: No alarms are generated and

no protection actions are performed.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

C Parameter Description

Issue 02 (2021-04-15)

261

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands