Huawei FusionCol8000-E240 User Manual Download Page 219

Page: 219 / 305

Figure 8-28 Separating the suction and discharge welding joints

(1) Suction port

(2) Discharge port

NO TICE

After removing the compressor, block the suction inlet and exhaust outlet

immediately to ensure the system cleanness and prevent water from entering.

2. Use a 13# socket wrench (or solid wrench) to remove the four nut washers

and spring washers that secure the compressor and remove the compressor.

NO TICE

Do not hold the suction inlet and exhaust outlet to move the compressor.

Figure 8-29 Removing a compressor

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

210

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands