Huawei FusionCol8000-E240 User Manual Download Page 145

Page: 145 / 305

8.2.1 Monthly Maintenance

Table 8-1 Monthly maintenance checklist

Item

Expected Result

Troubleshooting

Air filter

The air filter is clean and not

blocked.

● The outdoor intake air filter

(level: G3) cannot be cleaned

with water. It is recommended

that the outdoor intake air filter

be replaced every six months.

● The return air filter cannot be

cleaned with water. It is

recommended that the return

air filter be replaced every six

months.

The air filter is not damaged

or distorted.

Replace the air filter.

Water

tank

The float has no scale.

Clean up the scale on the liquid

level sensor when the device is

shut down.

The water tank filter is not

blocked.

Clean up the foreign matter on the

surface of the water tank filter.

Compresso

The compressor is secured.

Tighten screws if the compressor is

not secured.

The operating compressor

generates no metal friction

noise or collision noise from

inside.

Replace the compressor.

Pipe

The refrigerant pipe does not

leak or corrode, and is

properly wrapped with

thermal insulation foam.

Repair the leakage points and

rewrap thermal insulation foam.

Wear working gloves and

touch the needle valve and

soldering points of the

refrigerant pipe. There are no

oil stains.

If there are oil stains, check

whether the suction and discharge

pressure of the compressor is

within the normal ranges. If the

pressure is beyond the normal

range, contact Huawei technical

support.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

136

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands