Huawei FusionCol8000-E240 User Manual Download Page 268

Page: 268 / 305

Parameter Description

Table C-1 Parameter description

Menu

Parameter

Description

Settings > User

Settings

Language

Specifies the display language of the

display module.

Date format

Specifies the date display format of the

display module.

Date

settings

Specifies the date displayed on the

display module.

Time zone

Specifies the time zone of the display

module.

Time

Specifies the time displayed on the

display module.

LCD

password

complexity

check

Checks password complexity.

Password

Changes the password of the current

LCD

backlight

Off delay

Specifies the time of no operation after

which the display module backlight turns

off.

Key lifecycle

Specifies the key lifecycle.

Settings > Comm

Settings > WAN IP

Settings

For details, see the section "Setting Communications

Parameters."

Settings > Comm

Settings > LAN IP

Settings

For details, see the section "Setting Communications

Parameters."

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

C Parameter Description

Issue 02 (2021-04-15)

259

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands