Huawei FusionCol8000-E240 User Manual Download Page 249

Page: 249 / 305

Step 5 Start the unit, set the indoor fan speed to the maximum value, and read the

pressures measured at the positive and negative pressure points.

NO TE

Choose Maint > Diagnostic Mode > Enter and set the indoor fan speed to the maximum

value.

Step 6 Tap Start on the home screen. Ensure that the device is running normally without

any alarms.

Step 7 Log in to the WebUI as user admin, choose Settings > System Settings > System

Control > Advanced, and set Static pressure.

Step 8 Choose Running > Status Summary and view the value of air volume.

NO TE

● Static pressure setting = Pressure measured at the positive pressure point – Pressure

measured at the negative pressure point.

● User operator can access customer and delivery parameters. The parameters on the

Advanced menu are delivery parameters. User admin can access customer, delivery,

maintenance, and R&D parameters. The parameters on the Advanced menu are R&D

parameters.

● To prevent the effect of misoperations on the system, log in as user operator before

modifying parameters. Confirm with Huawei technical support before modifying

parameters which cannot be modified by user operator. Otherwise, Huawei will not be

liable for any consequences of the modification performed by the user.

● Only certified professionals are allowed to modify advanced parameters of smart

cooling products. Unauthorized modifications can result in smart cooling product

malfunction and even damage.

Step 9 Remove the pressure tubes and seal the holes.

----End

9.1.13 How Do I Check Whether Group Upgrade Is Supported

in a Scenario?

During group upgrade, the unit that is being upgraded is shut down and then

restarted. Ensure that the cooling capacity of the remaining units meets the

cooling requirements to avoid insufficient cooling capacity.

Table 9-1 Networking scenarios for group upgrade

Networking

Scenario

Monitoring

System

Networking

Teamwork

Networking

Group Upgrade

Status

FE monitoring

FE teamwork

Supported

FE monitoring

CAN teamwork

Supported

RS485 monitoring FE teamwork

Supported

RS485 monitoring CAN teamwork

Not supported

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

9 FAQ

Issue 02 (2021-04-15)

240

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands