Huawei FusionCol8000-E240 User Manual Download Page 178

Page: 178 / 305

Alarm ID

Alarm Name

Alarm

Severity

Possible Cause

Solution

A280-01

Power frequency

abnormal
Backup power

frequency abnormal
Auxiliary cooling

power frequency

abnormal
Auxiliary cooling

backup power

frequency abnormal

Major

● The power supply

frequency is below

the lower

threshold.

● The SPD and

voltage detection

board is faulty.

1. Check the power

supply frequency,

and ensure that it

is within the

working range.

2. Replace the SPD

and voltage

detection board.

A280-02

Power frequency

abnormal
Backup power

frequency abnormal
Auxiliary cooling

power frequency

abnormal
Auxiliary cooling

backup power

frequency abnormal

Major

● The power supply

frequency exceeds

the upper

threshold.

● The SPD and

voltage detection

board is faulty.

1. Check the power

supply frequency,

and ensure that it

is within the

working range.

2. Replace the SPD

and voltage

detection board.

A281-04
A281-08
A281-10

Power voltage

abnormal
Backup power voltage

abnormal
Auxiliary cooling

power voltage

abnormal
Auxiliary cooling

backup power voltage

abnormal

Major

● The power supply

voltage is below

the lower

threshold.

● The cables to the

SPD and voltage

detection board are

loose or damaged.

● The SPD and

voltage detection

board is faulty.

1. Check that the

power supply

voltage is within

the operating

range.

2. Check the cable

connection to the

SPD and voltage

detection board.

3. Replace the SPD

and voltage

detection board.

A281-20
A281-40
A281-80

Power voltage

abnormal
Backup power voltage

abnormal
Auxiliary cooling

power voltage

abnormal
Auxiliary cooling

backup power voltage

abnormal

Major

● The power supply

voltage exceeds the

upper threshold.

● The SPD and

voltage detection

board is faulty.

1. Check that the

power supply

voltage is within

the operating

range.

2. Replace the SPD

and voltage

detection board.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

169

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands