Huawei FusionCol8000-E240 User Manual Download Page 206

Page: 206 / 305

NO TICE

Exercise caution because the device is still energized after it is shut down on the

screen of the display module.

Step 2 Remove the outdoor intake air filter.
Step 3 Remove the indoor return air T/H sensor. Cut off the cable tie that secures the

cable, remove the screws from the sheet metal fastener of the T/H sensor, push

the baffle plate, and remove the T/H sensor and the sheet metal fastener.

Figure 8-13 Removing the T/H sensor sheet metal

Figure 8-14 Removing a T/H sensor

Step 4 Remove the outdoor intake air T/H sensor. Remove the screws from the sheet

metal fastener of the T/H sensor.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

197

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands