manualshive.com logo in svg

Huawei FusionCol8000-E240, User Manual

The Huawei FusionCol8000-E240 is a powerful networking device designed to enhance connectivity in your home or office. With its advanced features and seamless performance, this product delivers exceptional user experiences. Easily access the User Manual for this device and download it for free from manualshive.com to optimize your usage.

Share
Download
background image

Menu

Parameter

Description

Balance of

water and

electricity

consumption

Select the optimal operation mode based

on the water price and electricity price.

Wet mode

startup

temperature

Enable the wet mode when the ambient

temperature is higher than the preset

temperature.

Exhaust fan

speed when

the auxiliary

cooling

starts

Sets the minimum rotational speed of

the exhaust fan required for starting

auxiliary cooling.

Settings > System

Settings > T/H

Sensor

Temperature

and

humidity

control type

This parameter can be set to Cold aisle,

Hot aisle, Return air, or Supply air

based on site requirements. The

temperature and humidity setpoints

corresponding to the selected control

mode are enabled.

Temperature

control

mode

Set the temperature inside the room or

aisles based on the Average value, Max

value, or Min value of the temperatures

collected by each sensor.

Temperature

setpoint

After Temperature and humidity

control type and the temperature value

under this type are set, the device

performs cooling or heating based on the

settings.

Humidity

setpoint

After Temperature and humidity

control type and the humidity value

under this type are set, the device

performs humidifying or dehumidifying

based on the settings.

Exhaust air

high

temperature

protection

When the exhaust air temperature

reaches the threshold, the compressor

frequency is reduced or the compressor

stops running to avoid fire alarms.

Cold aisle

sensor*

You can enable or disable the cold aisle

sensors.

Hot aisle

sensor*

You can enable or disable the hot aisle

sensors.

Outdoor

intake air

sensor*

Outdoor intake air sensor* can be set to

Enable or Disable.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

C Parameter Description

Issue 02 (2021-04-15)

Copyright © Huawei Technologies Co., Ltd.

267

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E240

CAB PS11 Assembly Instructions Manual preview
PS11
Brand: CAB Pages: 10
ZERO GRAVITY SR Series Installation Manual preview
SR Series
Brand: ZERO GRAVITY Pages: 6
NARGESA TS10 Instruction Book preview
TS10
Brand: NARGESA Pages: 27
Endress+Hauser Condumax CLS15 Operating Instructions Manual preview
Condumax CLS15
Brand: Endress+Hauser Pages: 28
JETBAG 320 Fitting Instructions Manual preview
320
Brand: JETBAG Pages: 44
Laser 4832 Manual preview
4832
Brand: Laser Pages: 8
Oki C5100n Installation Instructions Manual preview
C5100n
Brand: Oki Pages: 20
Tao Motor TBR7 Installation Manual preview
TBR7
Brand: Tao Motor Pages: 3
Waterpik WP-650 Quick Start Manual preview
WP-650
Brand: Waterpik Pages: 2
Bose ShowMatch DeltaQ SMGSB Safety And Installation Manual preview
ShowMatch DeltaQ SMGSB
Brand: Bose Pages: 2
TBB power Energy Hub EH128L User Manual preview
Energy Hub EH128L
Brand: TBB power Pages: 24
Hama 00183354 Operating Instruction preview
00183354
Brand: Hama Pages: 38
R&G FI0054BK Fitting Instructions preview
FI0054BK
Brand: R&G Pages: 4
Rola LRSA2 Pack Contents & Fitting Instructions preview
LRSA2
Brand: Rola Pages: 3
U.S. General 95904 Operating Instructions preview
95904
Brand: U.S. General Pages: 4
Pilz PSEN cs1.1p Operating Instructions Manual preview
PSEN cs1.1p
Brand: Pilz Pages: 8
JETI model MBar EX User Manual preview
MBar EX
Brand: JETI model Pages: 7
Gordon AirPlay AirRing Large Owner'S Manual preview
AirRing Large
Brand: Gordon AirPlay Pages: 7

Brands by name

Popular brands

Load more brands