Huawei FusionCol8000-E240 User Manual Download Page 34 | Manualshive

Page: 34 / 305

background image

Installation Requirements

NO TICE

If the total actual load of servers for each equipment is less than 10% of the rated

cooling capacity or the equipment room is not properly sealed, the humidity in the

equipment room may exceed the upper limit, which is not a product quality issue

and should be dealt with by adding a dehumidifier.

Table 2-4 Installation requirements

Item

Specifications (Building

Scenario)

Specifications (FDC Scenario)

Transportatio

n passage

Width: > 3000 mm, height: >

4000 mm

N/A

Foundation

Bearing capacity of each

support point: > 1515 kg (four

support points in standard

working conditions)

Bearing capacity of each

support point: > 3163 kg (four

support points in standard

working conditions)

Water

quality

Specific requirements:
● Filtering level ≥ 89 μm
● 5 < Ph < 8.5
● Conductivity < 1300 μS/cm
● Total hardness < 100 mg/L
● Total alkalinity < 200 mg/L
● Chloride < 250 mg/L
● Organic matter < 3 mg/L
● Silicon dioxide < 10 mg/L

NOTE

If the water quality does not meet the requirements, the precooling

module maintenance frequency increases.

Power

distribution

Leakage circuit breakers are not recommended for the main

power route. If a leakage circuit breaker is required by the

customer or local regulations, select the residual current circuit

breaker (RCCB) that is insensitive to single-phase DC pulsation

and transient impulse current.

Note: If the requirements are not met, contact Huawei technical support for an

optimized solution.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Issue 02 (2021-04-15)

Copyright © Huawei Technologies Co., Ltd.

25

«
...
32
33
34
35
36
...
»

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E240

Brand: Y-cam Pages: 12

Brand: Samsung Pages: 7

Brand: BAC Pages: 36

Brand: Baader Planetarium Pages: 6

Brand: Hama Pages: 10

Brand: M7 SPEED Pages: 11

Brand: S&B Filters Pages: 7

Brand: Yakima Pages: 8

2 SD Card Memory Module NI 9802

Brand: National Instruments Pages: 16

Brand: Montech Pages: 17

Brand: Shenzhen Pages: 13

Powerbridge TSV

Brand: Fishman Pages: 2

Brand: Prorack Pages: 14

Brand: Temposonics Pages: 25

Brand: Berlebach Pages: 2

Brand: Moza Pages: 57

Brand: Nauticam Pages: 33

Telaire Ventostat T8100 NS Series

Brand: Amphenol Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands