Huawei FusionCol8000-E240 User Manual Download Page 170

Page: 170 / 305

Alarm ID

Alarm Name

Alarm

Severity

Possible Cause

Solution

A094-01

Low humidity alarm

Warning

● The ambient

humidity is below

the lower

threshold.

● The temperature

and humidity

sensor is not

installed in a

proper position.

● The low humidity

alarm threshold is

inappropriate.

● The value detected

by the temperature

and humidity

sensor is different

from the actual

value.

1. Measure the

ambient humidity.

2. Adjust the position

of the temperature

and humidity

sensor.

3. Adjust the low

humidity alarm

threshold.

4. Calibrate or replace

the temperature

and humidity

sensor.

A105-01

Indoor fan failure

alarm

Critical

● The accumulated

runtime of the fan

exceeds the alarm

threshold.

● The cable to the

fan is not

connected properly.

● The power supply

to the fan is

abnormal.

1. Maintain or replace

the fan, and clear

the accumulated

runtime.

2. Check the cable

connection to the

fan.

3. Check the power

supply to the fan.

A105-01

Exhaust fan function

failure alarm

Critical

● The fan is faulty.
● The cable to the

fan is not

connected properly.

● The power supply

to the fan is

abnormal.

1. Maintain or replace

the fan.

2. Check the cable

connection to the

fan.

3. Check the power

supply to the fan.

A118-01
A118-02

Backup power failure

alarm
Primary power failure

alarm

Major

The power supply is

faulty.

Check the power

supply.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

161

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands