
ET User’s Guide
9-23
Specifications
Table 9-6
Test Port Input (continued)
a. The System Dynamic Range is calculated as the difference between the receiver noise floor
and the minimum of either the source maximum output (maximum power setting minus out-
put power level accuracy) or the receiver maximum input. System Dynamic Range applies to
transmission measurements only, since reflection measurements are limited by directivity.
The System Dynamic Range for HP 8714 ET/ES 75 W analyzers is not a specification for fre-
quencies >2 GHz; it is a characteristic. For the HP 8712ES/8714ES, external broadband detec-
tors will provide more dynamic range than the internal broadband detectors.
b. Option 1E1 adds a 60 dB step attenuator to the HP 8712ET/8714ET.
HP 8712ET/ES and HP 8714ET/ES Test Port Input
Description
Spec.
(in dB)
Typical
(in dB)
System Bandwidths:
Fine
(15 Hz)
Fine
(15 Hz)
Med Wide
(4000 Hz)
Wide
(6500 Hz)
System Dynamic Range
a
(continued)
HP 8714ET:
50
Ω
:
With Attenuator Option 1E1
b
:
Narrowband
112
120
95
57
Broadband (Internal)
57
64
57
41
Without Attenuator Option 1E1
Narrowband
114
121
96
58
Broadband (Internal)
59
65
58
42
75
Ω
:
With Attenuator Option 1E1
:
Narrowband
107
115
90
52
Broadband (Internal)
50
58
51
36
Without Attenuator Option 1E1
Narrowband
110
116
91
53
Broadband (Internal)
53
59
52
37
Summary of Contents for HP 8712ET
