
8-84
ET User’s Guide
Hardkey/Softkey Reference
S
Softkey in the spur avoid options menu. If this option is selected, the
analyzer switches between the default and an alternate configuration
during a sweep to avoid spurs.
NOTE
Sweeptime usually increases when this option is
selected.
See
“Reducing Trace Noise” on page 5-12
CAUTION
The measurement calibration must be performed
with the same spur avoid option used in the
measurement or your results may be invalid.
Access Keys:
Softkey in the source
. Displays selections for spur avoidance:
dither, spur avoid, or none.
(Option 100 only) Softkey in the cable or measurement menus. Selects
the structural return loss (SRL) measurement. See your Option 100
User's Guide Supplement for information.
Access Keys:
or
or
Softkey in the utilities menu. Allows you to set the number of bytes in
the stack size by using the analyzer’s numeric keypad.
Access Keys:
Softkey in two menus:
and
.
1. In
menu, sets the start frequency of the source. Minimum
frequency is 300 kHz. When start is selected, the other frequency
parameter that must be defined is stop.
See
“Entering Measurement Parameters” on page 2-4
information.
2. In
menu, starts print or plot as set in the select copy
port menu.
See
“Printing and Plotting Measurement Results” on page 4-77
for
more information.
Spur Avoid
MENU
Spur Avoid Options
Spur Avoid
Options
MENU
SRL
BEGIN
Cable
MEAS 1
MEAS 2
Stack Size
SYSTEM OPTIONS
IBASIC Utilities
Start
FREQ
HARDCOPY
FREQ
HARDCOPY
Summary of Contents for HP 8712ET
