HORNER EXLW PRIME Series User Manual Download

Page: 7 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

7 | 201

Port Descriptions .................................................................................................................. 108

10.3

Wiring and Dip Switches ..................................................................................................... 108

10.4

RS485 Termination .............................................................................................................. 109

10.5

RS485 Biasing ....................................................................................................................... 109

10.6

Cscape Programming via Serial Port ................................................................................. 110

10.7

Ladder-Controlled Serial Communication ........................................................................ 110

10.8

Configuration via Mini-B USB .............................................................................................. 110

CHAPTER 11:

CAN Communications .................................................................................................... 111

11.1

Overview ........................................................................................................................................ 111

11.2

Port Description ........................................................................................................................... 111

11.3

CAN Port Wiring ........................................................................................................................... 111

11.4

Cscape Programming via CAN ................................................................................................ 112

11.5

Ladder-Controlled CAN Communication .............................................................................. 112

11.6

Using CAN for I/O Expansion (Network I/O) ........................................................................ 112

CHAPTER 12:

ETHERENET COMMUNICATION ................................................................................. 113

12.1

Ethernet Overview ..................................................................................................................... 113

12.2

Ethernet Module Protocols and Features ............................................................................ 113

12.3

Ethernet System Requirements ............................................................................................. 114

12.4

Ethernet Module Specifications .......................................................................................... 114

12.5

Ethernet Module Configuration .......................................................................................... 115

12.6

Ethernet Configuration

–

IP Parameters .......................................................................... 119

12.7

Ethernet Module Protocol Configuration ............................................................................. 119

CHAPTER 13:

DOWNLOADABLE COMMUNICATION PROTOCOLS .............................................120

13.1

Overview ......................................................................................................................................120

13.2

Protocol Config .......................................................................................................................... 122

13.3

Network Configuration............................................................................................................. 123

13.4

Device List and Device Configuration .............................................................................. 125

13.5

Scan List ...................................................................................................................................... 126

13.6

Data Mapping Configuration (Scan List Entry) .............................................................. 127

CHAPTER 14:

USER INTERFACE......................................................................................................... 129

14.1

Overview ...................................................................................................................................... 129

14.2

Screen Specifications ........................................................................................................... 129

14.2

Displaying and Entering Data ............................................................................................. 130

14.3

Alpha-numeric Keypad .......................................................................................................... 131

14.4

Screen Navigation ................................................................................................................. 133

14.5

Ladder Based Screen Navigation ...................................................................................... 134

14.6

Beeper Acknowledgement .................................................................................................. 135

14.7

Touch (Slip) Sensitivity ........................................................................................................ 135

14.8

Alarms ...................................................................................................................................... 136

14.9

Removable Media .................................................................................................................. 138

14.10

Screen Saver.......................................................................................................................... 140

14.11

Screen Brightness ................................................................................................................ 140

14.12

Touch Screen Pressure ......................................................................................................... 141

CHAPTER 15:

VIDEO OBJECT for EXLW/XLW PRIME .................................................................. 143

15.1

Video Object Overview ............................................................................................................. 143

15.2

Opening Video Object in Cscape ....................................................................................... 144

15.3

Video Properties: Video Type ................................................................................................. 147

15.4

Video Properties: Control ................................................................................................... 148

15.5

Configuring Display Properties ......................................................................................... 149

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands