HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 69 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

69 | 201

7.3.2 Communicating via On Board Ethernet Port

From Cscape go to Controller

→

Hardware Configure and do auto configuration for the

connected controller, Click on Config of Ethernet

→

Module Setup.

The IP address, Net Mask, and Gateway of the controller may be temporarily set from the
System Menu under the Set Networks menu item. Once running or power cycled, the
configuration will come from the Cscape configuration stored in the unit.

In Module configuration dialog go to IP Address field enter unused IP Address and configure
unused registers in Register field & then click OK. Screenshot for the same as follows:

Figure 7.6

–

LAN1 Configuration Dialog

Download the configuration in to Controller. Connect LAN cable to the Controller in default
LAN Port.

From Cscape go to Tools

→

Editor Options

→

Communication Port

→

Hardware Configure.

Select Ethernet and enter IP address which is configured in the file. Select mode as XL Series
mode from drop down list.

The controller should get connected to Cscape. If communications are successful, the target
indicator should show the mode of the controller Target: yy(R) as shown in the status section
above.

«
...
67
68
69
70
71
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: UNITED Pages: 22

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 124

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 114

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 8

ECL Comfort 296

Brand: Danfoss Pages: 159

VLT AutomationDrive FC 301

Brand: Danfoss Pages: 78

Brand: Danfoss Pages: 20

ECL Comfort 210

Brand: Danfoss Pages: 12

ECL Comfort 110

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 64

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands