HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 115 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

115 | 201

12.5 Ethernet Module Configuration

NOTE: The following configuration is required for all applications regardless of the protocols
used. Additional configuration procedures must be performed for each protocol used.

To configure the Ethernet Module, use Cscape Programming Software to perform the
following steps:

1.

On the main Cscape screen, select the Controller

→

Hardware Configuration sub-

menu to open the Hardware Configuration dialog (Figure 12.1).

2.

If configuring a different OCS Model than the one shown in the Hardware
Configuration dialog, click on the topmost Config button, select the desired OCS
Model, and then click OK.

Figure 12.1

–

Hardware Configuration Dialog

«
...
113
114
115
116
117
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: 7bit Pages: 2

Brand: Jafar Pages: 15

Brand: Samson Pages: 73

Brand: jbc Pages: 44

Brand: jbc Pages: 8

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Nedap Pages: 20

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: Balboa Water Group Pages: 88

Brand: ABB Pages: 2

Brand: µ-Dimension Pages: 48

Brand: µ-Dimension Pages: 2

Brand: D&R ELECTRONICS Pages: 12

Q Module WFZ16.Ox

Brand: QUNDIS Pages: 24

Brand: Delabie Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands