HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 181 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

181 | 201

CHAPTER 21: XLW BACK-UP BATTERY

The following information pertains to the XL and RCC OCS units running 14.24 firmware and
later.  This does NOT apply to the Prime Series. Please refer to the next chapter for
information on the Prime Series backup battery.

NOTE: For more details on the back-up battery, refer to the Battery Manual [MAN1142].

21.1 Overview

The XLW has an advanced battery system that uses a rechargeable lithium-ion battery. The
battery powers the real time clock when power is removed and is needed for register data
retention. Does not include the XLW Prime.

21.2 Storing Register Contents

The OCS controllers with rechargeable batteries write register data to high-speed RAM when
connected to DC power. When this power is lost, critical circuits switch over and run-on batter
power for about 1/10 of a second. During this time, register and other retentive data is saved
away to FLASH memory. The clock continues to run on the battery at a much lower power.
The battery is designed to last well over a year in this state. Once power is restored, the
battery recharges in eight (8) hours or less.

21.3 Battery Life

The battery is designed to last 300 full charges to 1000 partial charge cycles or 7 to 10 years.
Because typical operation does not drain the battery, the 1000 charge cycles should never be
reached and the 7 to 10-year aging of the battery would limit its useful life. The battery is
designed to be replaced.

21.4 Lithium Battery Safety

Many of the publicized battery issues are a result of using multiple batteries of flexible battery
packs. The OCS uses a small, single cell in a metal enclosure. The battery is UL recognized and
comes from quality suppliers. The OCS has safety circuitry built into the charging IC and
additional external protection including fusing. These circuits were closely evaluated by UL
and Horner engineering for use in hazardous environments.

«
...
179
180
181
182
183
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

Brand: Samsung Pages: 32

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brand: NAiS Pages: 144

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: Casambi Pages: 2

Brand: GEA Pages: 13

653 - AE Series

Brand: VAT Pages: 103

Brand: Harman Pages: 20

Brand: Intermatic Pages: 3

Brand: Leggett & Platt Pages: 20

Brand: Belimo Pages: 9

Brand: XP Metal Detectors Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands