HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 151 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

151 | 201

16.3 File System for microSD cards

The microSD Memory slot uses the PC-compatible FAT32 File System. This means that a PC,
with a microSD-compatible card reader, can read files that have been written by the
EXLW/XLW PRIME OCS and can write files that can be read by the EXLW/XLW PRIME OCS.

However, the EXLW/XLW PRIME OCS does not support long filenames, but instead implements
the 8.3 filename format. This means that all file and directory names must consist of up to
eight (8) characters, followed by an optional dot, and an optional extension with up to three
(3) characters.

Directories and sub-directories can be nested up to 16 levels deep as long as each pathname
string does not exceed 147 characters.

16.4 Using the Removable Media Manager

The Removable Media Manager is an interactive EXLW/XLW PRIME OCS screen that performs
the following functions:

a.

Display number of total and free K bytes

b.

Browse file and directory lists

c.

Delete files and directories

d.

Format a microSD card

e.

Load and save application programs

f.

View screen capture bitmaps

The Removable Media Manager can be accessed via the System Menu or by using Cscape to
place a Removable Media Manager object on an application graphics screen.

Figure 16.2

–

Removable Media Submenu

«
...
149
150
151
152
153
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

vlt soft starter mcd 500

Brand: Danfoss Pages: 96

Brand: Zeagle Pages: 37

Brand: Vanderbilt Pages: 2

Brand: Universal Remote Pages: 20

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

AMES 4000SS Series

Brand: Watts Pages: 8

Brand: Fancom Pages: 23

Brand: Beninca Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands