HORNER EXLW PRIME Series User Manual Download

Page: 157 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

157 | 201

CHAPTER 17: CLONE UNIT

17.1 Overview

‘Clone Unit’ feature allows the user to “clone” the OCS of the exact same model. This feature
“clones” application progr

am and unit settings stored in battery- backed RAM of an OCS into

the RM (refer

Removable Media

for details in using RM). It can then be used to clone a different

OCS (exact same model).

This feature can be used for:

Replacing an OCS by another unit of the same model.

Duplicating or “clone” units without a PC.

17.2 Clone

User needs to perform the following to Clone:

The ‘Clone Unit’ can be accessed by going to the ‘System Menu’ of the OCS. A new menu
“Clone Unit” has been added at the end of the main

System Menu as shown below:

Figure 17.1

–

System Menu

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands