HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 150 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

150 | 201

CHAPTER 16: REMOVABLE MEDIA

16.1 Overview

All EXLW/XLW PRIME OCS models provide a Removable Media slot, labeled Memory Card,
which supports standard microSD Flash memory cards. MicroSD cards can be used to save
and load applications, to capture graphics screens and to log data for later retrieval.

Figure 16.1

–

Removable microSD Memory Card Slot

16.2 Removable microSD Cards

When the microSD card format was introduced, it was originally called TransFlash. Cards labeled
either microSD or TransFlash, with up to 32GB of Flash memory, are compatible with the
EXLW/XLW PRIME OCS memory card slot (larger sizes were not tested at time of publication).

The memory card

slot is equipped with a “push

-in, push-

out” connector and a

microSD card can

be safely inserted into the Memory slot whether the EXLW/XLW PRIME OCS power is On or Off.

To install a microSD card:

Align its 8-pin gold edge connector down, facing the front of the

EXLW/XLW PRIME OCS unit; then carefully push it all the way into the Memory slot. Ensure that
it clicks into place.

To remove the microSD card

: Push in on the top of the card gently to release the spring. The

card pops out for removal.

«
...
148
149
150
151
152
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: S&C Pages: 40

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: K&K Pages: 6

Brand: Unipulse Pages: 99

Brand: Accutrol Pages: 25

Brand: Mainpine Pages: 16

Brand: Danfoss Pages: 20

Brand: Rain Bird Pages: 48

Brand: Sullair Pages: 31

Lux Intelligent

Brand: Advanced Pages: 62

Brand: intech 21 Pages: 15

Brand: Xsens Pages: 17

Brand: B meters Pages: 2

Brand: S&C Pages: 12

Brand: Velux Pages: 20

SWD Starter Kit

Brand: ez-wheel Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands