HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 23 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

23 | 201

3.6.5 Noise

Consider the impact on the panel layout design and clearance requirements if noise
suppression devices are needed. Be sure to maintain an adequate distance between the
EXLW/XLW PRIME OCS and noisy devices such as relays, motor starters, etc.

For details on output protection, especially when using contactors, solenoids, etc. see
MAN0962.

3.6.6 Shock and Vibration

The EXLW/XLW PRIME OCS has been designed to operate in typical industrial environments
that may inflict some shock and vibration on the unit. For applications that may inflict excessive
shock and vibration please use proper dampening techniques or relocate the EXLW/XLW PRIME
OCS to a location that minimizes shock and/or vibration.

3.6.7 Panel Layout Design and Clearance Checklist

The following list provides highlights of panel layout design factors:



Meets the electrical code and applicable standards for proper grounding, etc.?



Meets the panel manufacturer’s requirements for grounding, etc.?



Is the panel box properly connected to earth ground? Is the panel door properly
grounded? Has the appropriate procedure been followed to properly ground the
devices in the panel box and on the panel door?



Are minimum clearance requirements met? Can the panel door be easily opened
and closed? Is there adequate space between device bases as well as the sides of
the panel and wiring ducts?



Is the panel box deep enough to accommodate the EXLW/XLW PRIME OCS?



Is there adequate ventilation? Is the ambient temperature range maintained? Are
cooling or heating devices required?



Are noise suppression devices or isolation transformers required? Is there
adequate distance between the base of the EXLW/XLW PRIME OCS and noisy
devices such as relays or motor starters? Ensure that power and signal wires are
not routed in the same conduit.



Are there other requirements that impact the particular system, which need to be
considered?

«
...
21
22
23
24
25
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Value Point Pages: 7

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: Daikin Pages: 48

Brand: Daikin Pages: 77

Brand: Daikin Pages: 32

Brand: Daikin Pages: 46

Brand: Daikin Pages: 14

Brand: Daikin Pages: 16

Brand: Daikin Pages: 1

Brand: K'Nex Education Pages: 56

Brand: Taoglas Pages: 2

Brand: Zeta Pages: 44

Brand: Zamel Pages: 2

Brand: Ultraflex Pages: 7

Brand: National Instruments Pages: 78

Brand: Centurion Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands