HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 189 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

189 | 201

CHAPTER 23: MAINTENANCE

23.1 Firmware Updates

The EXLW/XLW PRIME OCS products contain field updatable firmware to allow new features to
be added to the product at a later time. Firmware updates should only be performed when a
new feature or correction is required.

23.2 How to Check for Current Firmware Revision

To check the firmware revision on a controller, open System Menu

→

View Status.

Warning: Firmware updates should only be performed when the equipment being controlled
by  the  EXLW/XLW  PRIME  OCS  is  in  a  safe,  non-operational  state.  Communication  or
hardware failures during the firmware update process can cause the controller to behave
erratically  resulting  in  injury  or  equipment  damage.  Make  sure  the  functions  of  the
equipment  work  properly  after  a  firmware  update  before  returning  the  device  to  an
operational mode.

«
...
187
188
189
190
191
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: OmarLift Pages: 14

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Parkside Pages: 86

Brand: Zamel Pages: 2

Brand: IBM Pages: 214

Brand: STIEBEL ELTRON Pages: 44

Brand: bihl+Wiedemann Pages: 16

Brand: FMS Pages: 108

Brand: Vega Pages: 28

Brand: WATSON Pages: 16

Brand: Danfoss Pages: 16

Brand: CAME Pages: 18

Brand: zeeltronic Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands