HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 187 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

187 | 201

CHAPTER 22: XLW PRIME BACK UP BATTERY

NOTE: For XL series controller battery information (not the Prime series) please refer to the
chapter above.

The  XLW  Prime  has  an  improved  memory  architecture  that  does  not  require  a  battery  for
program or register retention. The onboard lithium coin-cell battery runs the real time clock
and is user replaceable with an expected lifetime of seven (7) to ten (10) years. Environmental
conditions, including extreme temperatures and humidity, can affect battery life. If the battery
older than seven (7) to ten (10) years old, it is recommended that it be replaced as preventative
maintenance. NOTE: Use only the proper battery type listed.

NOTE: Use only the proper battery type listed.

WARNING: DO NOT USE IF BATTERY IS LEAKING OR HAS BEEN DAMAGED.

WARNING: LITHIUM BATTERIES MAY EXPLODE OR CATCH FIRE IF MISTREATED.
DO NOT RECHARGE, DISASSEMBLE, HEAT ABOVE 100° C (212° F) INCINERATE, OR
PUNCTURE.

WARNING: EXPLOSION HAZARD

–

BATTERIES MUST BE ONLY BE CHANGED IN A AREA

KNOWN TO BE NON-HAZARDOUS.

WARNING: Disposal of lithium batteries must be done in accordance with federal, state, and
local regulations. Be sure to consult with the appropriate regulatory agencies

before

disposing batteries. In addition, do not recharge, disassemble, heat or incinerate lithium
batteries.

WARNING: Do not make substitutions for the battery. Be sure to only use the authorized part
number to replace the battery.

«
...
185
186
187
188
189
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: 2gig Technologies Pages: 4

Brand: 2gig Technologies Pages: 2

Brand: G1SLE Pages: 2

Brand: Rane Pages: 2

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 400

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 466

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: Yamaha Pages: 2

Brand: TWR Lighting Pages: 49

Brand: Euromatic Pages: 20

Brand: VMK Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands